I uploaded the firmware on a NanoStation Loco M2, upgraded it, and was able to get to the initial setup page.

When I changed the node name, and my password, the unit rebooted, and now I can no longer get to the web page to log into the unit. I also get a red LED on the third LED from the left. Have no idea what that even means.

I can see this node from my linksys mesh node, but when I click the link it comes up with web page unavailable. 

I get no response when I ping 192.168.1.1, nslookup can't find the server.

No problem. Glad you got it working. As for the password, it is what you set it in step 4 from the bullet "enter a Password (twice)." The username remains the same: root.

Just wondering if anyone has messed around with putting BBHN on a "Hak5 Wifi Pineapple"?(check it out here   http://hakshop.myshopify.com/products/wifi-pineapple?variant=81044992)

If not, I have one and would be willing to (with proper direction) attempt it. The Pineapple already has a version of Open-WRT on it and runs from a micro sd card. I would think or I should say guess, that it would be something like installing on a Raspberry Pi. I am interested in using this because of the dual radios, (1) 2.4Ghz and (1) 5.8Ghz.

Correction: It runs on internal memory and has a micro sd slot. Mine shipped running a version of ATTITUDE ADJUSTMENT.

Again, I was just wondering so don't try and move the moon on this one.

Thanks,

KE8AVJ

Thanks for the help.

After everything being off over night, turning the wifi off and two or three try's to log on to the BBHN node it WORKED.

I completed step 4 to configure the mesh node it works, only thing is if I go back to SETUP it asks for a user name and password, root and hsmm do not work.  What is it now?

Other than that I guess I have a working mesh node, no one else in the area to check it out.

I'm very new to this, I just registered yesterday. I did a search and see no mention of the BEFW11S4 Linksys series. I suppose this means they are of little use? I have two of those. I also have a WRTG45G V8 which means it is also a coffee table decoration.

Guess I'll have to hunt around for something useful. I'm looking forward to playing with some new toys.

Thanks.

Dennis, K1YPP

Three things first come to my mind:
1) Did you unplug your network cable, wait about 10 seconds, and then plug it back into the node? What port did you plug the network cable into?
2) Have you tried flushing your internet browser cache and trying again? and
3) If your computer is WiFi-enabled, have you tried turning that off?

Do any of these search results help you out?
http://www.broadband-hamnet.org/hsmm-mesh-forums/view-postlist/forum-1-general/topic-701-cannot-access-webgui.html
http://www.broadband-hamnet.org/hsmm-mesh-forums/view-postlist/forum-5-problems-a-answers/topic-1274-cant-access-nodes.html

Just loaded latest firmware (bbhn-3.1.0-wrt54g-2.4-squashfs.bin) onto a WRT54g v2.2 with linksys firmware on it, followed the Firmware Installation Instructions by AD5OO.

Everything went fine through step 3, then it went bad at step 4, when I go to browser (http://localnode:8080/) there is no response, LAN or wireless.

What did I do wrong and how do I recover? Do I dare to reset it? This is my first try at doing this.

Thanks, Tom

wb7out@arrl.net

Do you have a packet trace of a good call and a failed call you could share?  Exactly 7 seconds sure sounds like a timer of some sort but that is awfully short for any standard SIP timers I can think of.