Broadband-Hamnet™ Forum :: Firmware
Board Index Latest Posts Welcome Guest   [Register]  [Login]
 Subject :Router not able to re-flash.. 2014-01-22- 03:57:12 
AE5XI
Member
Joined: 2013-12-16- 10:13:22
Posts: 4
Location: Las Cruces, NM

I have a problem and do not seem to find an answer any where on the net. The router was flashed with the BBHN firmware. Went in and changed the ID and Password and rebooted. Now able to get in to the router but not able to get in to the setup page. It will not take ID or Password. 

I want to re-flash the router. All the instructions say to open the Set up page, but if you are not able to get into it then not able to re-flash. I was going to re-flash with Linksys but not able to find the firmware since the router is no longer supported by Linksys. I looked all over and not able to find original firmware. 

Any suggestions. I have a router that I can not use reset or re-flash. 


Thanks
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-22- 04:06:03 
SM6SMY
Member
Joined: 2013-12-30- 11:51:52
Posts: 6
Location: 
Hi, Try user: root pwd: hsmm (default) Good Luck!! 73's de Peo SM6SMY
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-22- 04:09:54 
AE5XI
Member
Joined: 2013-12-16- 10:13:22
Posts: 4
Location: Las Cruces, NM
I tried that and did not work. I even tried user: root pwd: admin. Still no luck.
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-22- 04:25:31 
SM6SMY
Member
Joined: 2013-12-30- 11:51:52
Posts: 6
Location: 
Ok, try user: root pwd "The pwd that you have set" 73 de Peo SM6SMY
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-22- 19:20:36 
KB3UQE
Member
Joined: 2013-12-23- 01:38:54
Posts: 11
Location: Edgewood, Maryland
 
There is a walk through on linksys website on how to recover a bad flash.... I had to do that for 1 of mine because the nvram was corrupt and would not boot.... I ended up using that tool they supply to flash the hsmm file direct and worked very well
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-23- 01:27:32 
AE5XI
Member
Joined: 2013-12-16- 10:13:22
Posts: 4
Location: Las Cruces, NM
I tried Linksys and they do not support my WRT54GS V3, so not able to get the original firmware to be able to re-flash I already have BBHN on the router. Instructions for re-flashing for BBHN firmware is through the setup and I am not able to get into the set up page because the password or ID.
IP Logged
 Subject :Re:Router not able to re-flash.. 2014-01-23- 03:52:45 
sp2ong
Member
Joined: 2013-10-30- 10:57:25
Posts: 72
Location: 

Hi,

If you woluld like you can download from our WWW site firmware for WRT54GS v3. I have use this firmware to reflash my WRTGS v3 from firmware TOMATO to original Linksys firmware:

http://hamnet.ugu.pl/download/WRT54GSv3_4.71.4.001_fw.bin

After rflash to Linksys firmware I have load  BBHN firmware. You can put this firmware via tftp to WRT54. If you have problem with WRT54 bfeore reflash you can use reset with 30/30/30 folow with this link: 

http://dd-wrt.de/wiki/index.php/Recover_from_a_Bad_Flash

http://www.youtube.com/watch?v=IHUkPms7Blw
IP Logged
Last Edited On: 2014-01-23- 03:53:52 By sp2ong for the Reason
Page # 


Powered by ccBoard


SPONSORED AD: