Buddy of mine at work had this old router and knew of my HSMM project and just gave it to me.

I don't see it listed on the "Useable" device list.

Any useability at all for HSMM? 

If not just going to trash it as I am moving towards all Ubiquiti devices and probably going to sell off the other 3 WRT54GS's I have.

Thank god for Google!!!

http://wiki.openwrt.org/doc/howto/generic.failsafe

I have a WRT54GS version 1 router that had DD-WRT firmware on it. I followed the GUI install of BBHN firmware but now after the router reset it is in MESH AP mode ( ip of 172.27.0.1 ).

Can't find my saved link to how to do a master reset thru the telnet access way into the router.

Anyone have that link handy?

Here are the images I just took for screen captures off our Anritsu SiteMaster S332E. This is using the antenna that is labelled 25dBi for 2.4GHz purchased from eBay. (NOTE I AM NOT AN EXPERT WITH THE SITEMASTER.) I did not have the software installed to make actual images from the screen so these are just iPhone shots.

I am in no way an expert with the SiteMaster, so these images may be useless. However, here they are for reference. My initial impression with the plots is that it is not 25 dBi gain like the claim, however the coax is pretty small and it does not have designators to reference so it could be very lossy there. 

Appears to be an unrelated issue.

I would suggest DIRECT mode until a fix comes out.

DCARA Members,

Many of you have been asking for information as to which antennas and equipment I've purchased to go along with my Ubiquiti Rocket M2. For the sake of simplicity I am compiling the list here:

Ubiquiti Rocket M2 (many vendors available, purchase through club and we will have connectors and cable available soon.)

2.4 GHz 25dBi Yagi: http://www.ebay.com/itm/RP-SMA-2-4GHz-25-DBi-Wireless-WLAN-WiFi-Antenna-For-Yagi-Modem-PCI-Card-Router-/111329400253?pt=US_Directional_Network_Antennas&hash=item19ebbfd5bd

2.4GHz 12dBi Omni Directional: http://www.ebay.com/itm/TP-Link-2-4GHz-12dBi-Omni-Directional-Outdoor-Wireless-Vertical-Antenna-WIFI-/230933790877?pt=US_Directional_Network_Antennas&hash=item35c4ba009d

Sorry image link is not cooperating.

N-Maile to RP-SMA 24" Cable LMR-400 Ultraflex: http://www.l-com.com/coaxial-n-male-to-rp-sma-plug-400-ultra-flex-series-assembly-20-ft

All said and done with a little hunting I've only spent around $200 on the complete package. 

I will try those out and see what I can do, Im still stock with antennas right now though so it might be impossible until i get my hands on a yagi or the likes, just looking for a good source to buy from.

I'm not sure if 1.1.1 actually fixed the problem. Attached is the screenshot of my configuration setup for the 1.0.0 software. My computer interface is inet addr:172.27.0.5  Bcast:172.27.0.255  Mask:255.255.255.0.

With the 1.0.0 software everything worked. I could see all the nodes and get to them with my web browser as well as ping each 10.0.0.0/8 node. Not sure if there was some NAT going on in the router but it all worked.

With 1.1.1 I can only ping or access the local node, I can't ping or get to any attached node even though they show up as in the mesh. I can ssh into my local node and it can ping and see everyone but my computer on the lan can only see the local node.

Any ideas? Sounds like a NAT/MASQUERADE/Firewall change.?

KF7PSM - Peter

Attachments
 Screenshot-KF7PSM-NW2-setup1.png [144 KB] ::

Hi All

I'm building my WRT54G army and was wondering if anyone has a source for antennas in Ontario Canada region? Most of my setup would be mobile for now until i can convince a repeater group to start meshing. Any opinion on the off shore ebay deals?

Thanks

Shawn

You may need to clear the cashe in your browser for the update to show up. 

Clint 

Releases have been available since July 7th.

When will v.1.1.0 firmware for Linksys devices be available on the download page?